• 	(2.4 MB)

  Ideally suited for chemical, biotechnological and medical applications as well as for mass screenings
• Wear-free inductive VARIOMAG drive, effectiveness increased by microprocessor control
• Remote-controlled by separate control unit
• 6, 15 or 60 stirring points
• Speeds of 130 to 1.000 rpm
• Automatic start-up for safe acceleration of the magnetic stirrer
• Stirring volume up to 800 ml
• Suitable for 6 x 1.000 ml Erlenmeyer flasks (TELESYSTEM 6 and 15) or for 15 x 250 ml glass beakers (TELESYSTEM 6 and 15) or for 60 sampling vessels or test tubes (TELESYSTEM 60)
• Suitable also for other types or sizes of receptacles
• Large, easy-to-clean working surface
• Hermetically sealed stainless steel housing, making it inaccessible to water, dust or microorganisms; easy-to-clean housing with no cracks, joints or edges
• Ideally for use under conditions of high ambient humidity or in aggressive media
• Can be cleaned under running water
• Ideally suited for operation directly in water baths (up to +50 °C)
• Versions for operation directly in water baths (up to +50 °C) or at up to +200 °C in air are optionally available
• Sturdy and indestructible
• Limited suitability for use in incubators or climatic chambers and chemical resistance
• Immersible, can be used directly in the water bath
• Highly heat-resistant - up to +50 °C directly in the water bath, up to +95 °C directly in the water bath (special), and up to +200 °C in air (on request)
• Choice of 3 control units for different types of usage (see functional description on pages 32 and 33)
• Great range of features depending on the specifications of the control unit
• Ideally suited for system integration
• Ergonomic and convenient handling of e.g. submerged magnetic stirrers
• Safe low-voltage device.

• 	(2.4 MB)

  Ideally suited for chemical, biotechnological and medical applications as well as for mass screenings
• Wear-free inductive VARIOMAG drive, increased effectiveness by microprocessor control
• Direct-controlled
• Extremely wide speed range of 80 to 2.000 rpm
• Stirring bars turn evenly and without jerking, even at low speeds
• Digital display to facilitate exact speed settings
• Automatic start-up for safe acceleration of the stirrer
• Four different power settings (25/50/75/100 %), for larger quantities and more viscous liquids and reduced power for long-term operation, largely without heat generation
• Stirring volume up to 3.000 ml
• Suitable for 6 x 1.000 ml Erlenmeyer flasks, but also for larger single receptacles
• Large, easy-to-clean working surface
• Hermetically sealed stainless steel housing, making it inaccessible to water or dust; easy-to-clean housing with no cracks, joints or sharp edges
• A memory function stores the most recent settings, even when the device is taken off mains for a longer period of time
• Indestructible.

• 	(0.3 MB)

  The MAGNETIC STIRRER MS01 is a powerful and simple to use four position stainless still magnetic stirrer.

• PRODUCT FEATURES
• Four positions for effective mixing in different size flat bottom laboratory flasks.
• Compatibility with ELMI thermostat TW-2.03.
• Stainless still highly rugged and resistant housing.
• Can easily be integrated in different lab processes.

• PRODUCT BENEFITS
• It is specially designed to operate with ELMI water thermostat TW-2 series. Together with TW-2.03 heating functions it becomes possible to maintain highly accurate temperature maintenance as well as mixing efficiency control. Reliability, simple operation and noiseless operation make MS01 perfect assistant in any laboratory.

• 	(2.4 MB)

  BIOSYSTEM DIRECT
• For mixing microcarrier cultures, culture broths, and cell suspensions without destroying the cells
• Stirring bars turn very evenly and without jerking
• Direct-controlled
• Speeds of 5 to 120 rpm
• Automatic start-up for safe acceleration of the magnetic stirrer
• Stirring volume 25 to 5.000 ml
• Compact, flat design
• Sealed in a resistant stainless steel housing, thus suitable for use under conditions of high ambient humidity
• Impermeable to microorganisms; meets the hygienic requirements of the German safety regulations for genetic engineering
• Can be cleaned under running water
• Inexpensive

• BIOSYSTEM 4 DIRECT
• Identical with BIOSYSTEM DIRECT with regard to features, technology and applications, but with:
• 4 synchronized stirring points, rectangular arrangement
• Stirring volume up to 4 x 2.000 ml

Hint: The suitability of direct-controlled magnetic stirrers for use in incubators is limited, because the stirring power cannot be reduced. In addition, the integrated electronics heat the magnetic stirrer additionally.

• BIOSYSTEM
• For mixing microcarrier cultures, culture broths, and cell suspensions without destroying the cells
• Stirring bars turn very evenly and without jerking
• Remote-controlled by separately available BIOMODUL 40 B control unit
• Ideally suited for long-term heatless use even in CO2 incubators
• Speeds of 5 to 120 rpm
• Automatic start-up for safe acceleration of the stirring bar
• Stirring volume 25 to 20.000 ml
• Compact, flat design
• Sealed in a resistant stainless steel housing, thus suitable for use under conditions of high ambient humidity or directly in temperature-controlled water baths
• Impermeable to microorganisms; meets the requirements of the German safety regulations for genetic engineering
• Can be cleaned under running water
• Two drives may be synchronized (see data on BIOMODUL 40 B control unit on page 36)

• BIOSYSTEM 4
• Identical with BIOSYSTEM 1 with regard to features, technology and applications, but with:
• 4 synchronized stirring points, rectangular arrangement (linear arrangement optionally available)
• Stirring volume up to 4 x 5.000 ml

• 	(2.4 MB)

  Since 1981, the patented magnetic stirrers VARIOMAG have been setting new standards in magnetic stirring technology. The wear-free VARIOMAG magnetic stirring philosophy has a world-wide reputation for being reliable and practically indestructible.
• Conventional magnetic stirrers use an electrical motor spinning a permanent magnet, thus exerting a force on the magnetic stirring bar within the stirring vessel. In VARIOMAG Magnetic Stirrers, electrical motors and permanent magnets are replaced by four stationary magnetic coils through which a variable current flows, producing a rotating electromagnetic field.
• The inductive drives of VARIOMAG Magnetic Stirrers operate without any moving parts such as motors, belts, or mechanical bearings, making VARIOMAG Magnetic Stirrers 100% wear-free and maintenance-free. In addition, the VARIOMAG inductive drive can be hermetically sealed, making it inaccessible to water, dust or microorganisms. This is why VARIOMAG Magnetic Stirrers are particularly suitable for use under even the most difficult and demanding environmental conditions.
• 100% wear-free
• Maintenance-free
• Ultra-flat design, even miniaturized
• Constant speeds even in the event of viscosity changes
• With and without heater.

• 	(2.4 MB)

  MINI • MINI 20
• Wear-free inductive VARIOMAG drive
• Remote-controlled by separate control unit
• No larger than a one-cent coin
• Only 5 mm high
• Ideally suited for cuvettes 12 x 12 mm, suits any
• x 10 mm cuvett holder
• Ideal for integration in analytical devices, cuvette holders and photometers
• OEM versions on request
• Highly flexible foil cable, 0.3 mm thick
• MINI 20 is recommended for greater distances between the magnetic stirrer and the stirring vessel
• Mini, Mini 20, Micro, Micro 20 to use with TELEMODUL control unit (stirring power 7 watts) or TELEMODUL 20 C control unit (stirring power 20 watts)

• MICRO • MICRO 20
• Wear-free inductive VARIOMAG drive
• Remote-controlled by separate control unit
• No larger than a matchbox
• Only 16 mm in height
• Hermetically sealed in a resistant stainless steel housing, thus suitable for use under conditions of high ambient humidity or in aggressive media; impermeable to microorganisms
• Can be cleaned under running water
• Ideally suited for operation directly in water baths (up to +95 °C)
• Version for operation at up to +200 °C in air available (on request)
• Integrated M4-threaded bore for attaching the magnetic stirrer at the bottom of the housing
• Sturdy and indestructible